A New Type of Protective Weapon Based on the Creation of a Rotating Powerful Intensive Beam of Electro-Magnetic Waves (Emw) High Frequencies (Hf)

: Zhakatayev T. A., Kakimova K. Sh. A New Type of Protective Weapon Based on the Creation of a Rotating Powerful Intensive Beam of Electro-Magnetic Waves (Emw) High Frequencies (Hf). The idea is completely new. Therefore, we cannot indicate before history and analogues for comparison. A physical justification of the fundamentally new idea that a perpendicular alternating magnetic field rotating in a circle can be superimposed from the outside on a continuous directional flow of Hf Emw was carried out. Which will cause the entire continuous flow of the Hf Emw as a whole vortex cord to rotate. Possible options for using this new technical installation for protective purposes, in defensive hostilities have been analyzed. Like electronic blocking of all combat vehicles, missiles and shells. With wave Emw interlocking, radio isolation, they lose radio communication, orientation and aiming at the target. It can also be used to block the physical and mental activity of soldiers by affecting the brain and other vital organs of human functional activity. Semi-empirical formulas are given for calculating the spatial flow of Emw as a function of two cylindrical coordinates. Initial radiation is formed in resonance chamber of magnetron. You can use a traveling wave lamp. Mathematical modeling uses an analogy with the propagation of the jet stream. Gas dynamic analogy. Semi-empirical formulas were obtained for calculating the spatial flow of Emw as a function of two cylindrical coordinates. The calculation model is proposed to be used for Emw intensive flow calculation. The scheme of "collecting lens" for Emw flow is proposed. For practical application, it is proposed to work together with interested scientists and specialists.


Introduction
All types of weapons used by humanity so far have the following great drawback. From the point of view of physics, it is necessary to allocate a very large amount of thermal energy in a very small period of time and in a very small limited volume. That is, they are all based on the explosive action of any charge, a source of ultra-high energy. This characteristic applies simultaneously: to a gunshot (powder) bullet, and to an atomic bomb, and to a missile with a nuclear warhead of various exposure radius. From the point of view of modern scientific knowledge and achievements, these types of weapons are outdated. They have relatively low efficiency and very high financial costs. From the point of view of modern new, universal human positions -a tank, mines, guns and bombs can be called a very terrible, ridiculous, stupid, cruel and deeply immoral creation of humanity! Which must be destroyed, removed from the circulation of human use as soon as possible, like all other types of killing and destroying weapons. And we will prove their futility later. Is it not possible to somehow try to evaluate what is wild fascism, cruel, not permissible barbarism -to kill people in such a way that pieces of metal plunge into a living human body? Tear a living man to pieces? These are unacceptable barbarism and savagery. Created by God, an incredibly mysterious, very complex, unrecognizable and at the same time marvelous world has unlimited possibilities to implement measures to protect the lives of people, in the presence of economic, political or military pressure from some strong country in relation to another weaker country.
There will be significant benefits for humanity if many weapons are melted down into metal. Then they will make cases for computers.
Advanced developed weapons must meet new requirements and principles. For example, to have a remote effect on a combat vehicle, missile or mechanism, as a result of which it will become non-radio controlled, unusable. In other words, it will simply turn into a pile of useless metal. It is also possible to influence people -on soldiers of the enemy army. When blocking radio communications -they will become vulnerable and useless. The maximum that they can do (with isolation of communication) is shoot in all directions from a machine gun until the cartridges end.
As a result of a protracted, "soft," continuous influence on the soldiers, they can be taken out of mental balance and rest. For example, if you continuously from somewhere from afar, from places not reached, affect their brains. Such weak effects can cause unpredictable diseases. After which the soldier himself will not want to fight, or will not be able to do so. The new principles of "soft weapons" are simple and humane: to bring the soldier to ill health, after which he will leave the zone of active hostilities.
This scientific paper describes a new type of protective weapon based on a very powerful intense rotating beamelectromagnetic wave beams (EMW) from installations above high frequencies (microwave) of continuous influence. Which can be very far from the target.
Ultimately, we wish world peace and happiness to all mankind on earth.
The new protective weapon we invented is just protecting, protecting the world, stopping aggression, protecting the peace of ordinary and peaceful people throughout the earth. Who are sometimes defenseless to some aggressors and warlike people on the planet.

Theoretical Solution
In near-Earth outer space, at some distance from the earth's surface (at a level above the ozone layer), the following simple equipment can be located, which continuously emits high frequency electromagnetic waves (HF EMW) or above high frequencies (AHF EMW), microwave. The output portions, the output guides of which are shown in Figures 1. A, B are output parts designed for powerful magnetrons. The C-structure of output (radiating) part for EMW not above high frequency, not microwave. Various magnetrons can be used as sources of powerful microwave EMW [1][2][3][4]. In these sources they are described in sufficient detail, so let us not dwell on the description of their design and principle of operation.
In part A) and B): 1 -the channel, which is connected in resonance wave chamber of magnetron, 2 -the output wave channel of cylindrical shape, (3) -one of three active windings of three-phase winding to guide the external circular alternating magnetic field . Electromagnetic waves (EMW) exit the channel 1 of the magnetron. Which is called a resonance camera. 2 -is the most output part, the terminal part. X-direction of EMW output, traveling direction.
In part C): 1-hemispherical reflector of the EMW, 2 -НF EMW, 3 -EMW source, powerful lamp (LG) EMW medium frequencies, 4 -external source of transverse magnetic field of rotating around, F -focus of a reflective hemisphere. 4 and -external coils which create variable rotating around (on external perimeter of the circular channel) magnetic field of . This variable field of can be created on the basis of the operation of the running field in the stator winding of the three phase AC motor, as shown in Figure 2. Details of the running field creation in the three-phase winding are described in [5,6], so we will not stop here.  with an angular speed . This stream is continuous. In this way, the flow of the EMW will turn into a rotating vortex cord. We can call it the vortex tube of the EMW. This is shown in Figure 3. The driver, exciter coil is shown in Figure 1. The application of the three-phase stator winding principle has played a key role here.  Figure 1.
) is the geometry of the location of the three-winding coil to create rotating magnetic field in a circle. 120 о . To Figure 3-А: 1-vortex cord, corridor, 2 -EMW source, 3 -surface of ground of the earth or some object, where it is directed.
The vortex tube inside consists of solid flow (matter) of the EMW. From the flux of quanta particles of EMW. The EMW vortex involves literally in circular rotational motion all particles which are inside this volume. These can be real physical particles: electrons, protons, neutrons, alpha, mu, pi, ka -particles, etc. Inside this vortex tube (cord) there are also molecules of , , С and other gaseous substances. Gaseous substances may be in the atomic state. These atoms and molecules are generally neutral. But at some points in time, they polarize for a short time. A circularly rotating electromagnetic field will rotate these polarized atoms and molecules. For our case particles we will also call field quanta: gamma, X-ray, ultraviolet light, infrared radiation. Waves and quanta of another wave spectrum unknown to us may be present. The fact that in space all kinds of these particles and radiation are available is a positive side of the new technology and installation we are creating.
Particles that move in circular orbits gradually move away from the center to the outside of cylinder 1 and 2. Due to centrifugal force and centrifugal acceleration Near the axis F-X-O some vacuum of airspace is formed. All charged and polarized "heavy" particles will gather near the outer layer of the cylinder. There where is no rotating magnetic field of any more. Or his action will be weak. This boundary layer of accumulated charged or polarized particles will be called a conditionally "wall" of the cylinder. Thus, the wall (thickened layer of particles) will serve as a reflective surface that will not allow the EMW to disengage from the cylinder, from the corridor. Further into the surrounding space. The fact that the eddy cord of the EMW will go far, up to the surface of the earth, is confirmed by Helmholtz's theory of vortices [7,8]. It's from a fluid mechanics course. See Figure 3.
The principle of rotation of the vortex tube, the EMW beam as a whole cord is consistent, does not contradict the following theories: 1) transverse EMW, 2) longitudinal EMW, 3) quantum, corpuscular properties of EMW. That they have some mechanical impulse [9][10][11]. It is the rotation that is a strong, effective side of this protective device. This is much stronger than the direct passage of the EMW through the substance. There is a drilling effect.
Thus, it is possible to create a combat protective weapon of a slow, continuous, "soft," protracted type of action. Since all types of cosmic radiation listed above, cosmic particles are dangerous for all wildlife on earth. Ultraviolet radiation alone does not travel to the ground as a result of the protective effect of the ozone layer. This plant makes it possible to easily discharge, accelerate, weaken the ozone layer. As a result, you can hit vast areas of the land where enemy troops are located.
Exposure to a concentrated dense beam of HF or microwave EMW is also very harmful to a living organism. Not to mention others, it can simply lead to internal overheating of the human organ. Which a person himself may simply not feel. Strong polarization of all kinds of molecules of a particular human organ will play a role. And an additional forced rotation in space is essentially forced mixing of liquid inside the human organ. Polarized atoms, molecules, macromolecules, or clusters will be very fond of the rotating vortex of EMW. This will have a very negative effect on the work of the brain and other vital organs of a person, a soldier. Can get out of normal operation.
The powerful, intensely rotating beam of the HF EMW will disable all radio-controlled missiles, aircraft, unmanned aerial vehicles and other combat installations as soon as it visits them. Thus, all types of enemy missiles and vehicles can be disabled by losing orientation in space and a radio control program. They will just fall.
You can point this ray (beam) at groups of enemy combat soldiers. For protection. In this case, the rotation flow of microwave EMW will lead to a human brain disorder. Unpredictable spoilage of some other vital human organs can also be caused. Mobile communication systems this person is not likely to be able to use normally. The impact will not seem small.
Sources of microwave EMW can be magnetrons, which are described in [1][2][3][4]. Figure 1-С -corresponds not to magnetron, but to weaker low-frequency radiation. For example, it is a powerful radio lamp (GU type) with an output to the L-C cascade. It is also possible to use klystrons and lamps of travelling and reflected waves with a high frequency.
Sometimes there is a need to change the relation of output and entrance diameters of an output section of the pipe in Figure 1, ⁄ . For such expanding or narrowing contours we propose to perform internal contours according to Vitoshinsky profile [7,8]. The main flexible profile is obtained, see Figure 1 -B, profile 2. Winding is desirably arranged closer to the narrow (smaller) part of loop 2. That there was the best penetration of field in depth of the channel.
Let us record the law of electromagnetic field energy conservation for cylindrical column 2 in Figure 3-B) [9 -11].
This means that the energy flows multiplied by the dimensions of the cross sections in sections 2 and 6 will be constant ....  Expression (2) can be written more accurately 6 01 23 7 8 .
Formulas (2), (3) mean that the results of jet currents, which are more or less well described in [12,13], may well be applied to solve the problem of expanding the energy flow of the EMW in the expanding cylindrical cone. Figure 4 shows the flow diagram of the ventilation turbulent axis symmetric jet. 9 8 -speed jets at nozzle outlet, m/s, 9 : -speed on OX axis. From the figure you can see how the jet pulse scatters over the transverse area of the jet flow. Line 4 is the velocity profile, line 5 is the transverse temperature profile in the same section. Thermal energy variation is greater, more intense than pulse dissipation. Thus, we have a complete gas dynamic analogy when calculating the distribution of the volumetric density of the EMW energy inside the vortex cord. From this gas-dynamic analogy, we obtained the following equation for calculating the spatial distribution of the volumetric density of wave energy where constants A and c are determined from an experiment with a beam at an arbitrary initial bulk density 8 at the outlet of the magnetron chamber, x, y are longitudinal and transverse coordinates. Equation (4) corresponds to a point source, that is, a source with a very small initial area. When radiating from a channel with a sufficiently large cross-sectional area, formula (3) should be written in the differential form and then integrated over the entire initial cross-sectional area of the jet according to (3), where 8 . Similar integration operations for jet currents are done in [12,13] for velocity, temperature and impurity concentration fields. For the case of ventilation jets at the initial final size. This was originally discussed in [14]. Where electrodynamics is little considered.  Figure 5 shows the diagram of the refractive "lens" for electromagnetic waves -EMW. 2 shows a solid cylindrical body of metallic material which reflects the EMW well. 3-7 are thin metal wire grids that also reflect EMW well. These grids in the inlet and outlet have bulges in the interior of the cylinder or otherwise of the reflective channel. These bulges are directed in different directions, what is at the entrance and what is at the exit. Thus, this design, conventionally called by us "lens for EMW," a slightly divergent beam of EMW at the input will radiate pen in the form of a slightly convergent beam of EMW at the output.
Sources [1][2][3][4] note that magnetrons are used in radars. They operate in the mode of short-term pulses. This prevents the electrodes from overheating. Wavelengths are on the order of several centimeters. Capacity can reach up to a thousand kilowatts [1][2][3][4].
(5) -represents the general law of energy conservation in the final volume of the airspace in the presence of an alternating electromagnetic field. Taking into account the emerging currents. There are no cross flows w on the boundary line B P ACD . They are considered negligible, see Figure 4.
We are able to solve fairly complex systems of integral and differential equations in partial derivatives. With a wide variation in boundary conditions. Based on numerical methods. With run and at repeated refinement of values of the first derivatives at each point of grid area [13]. Statistical physics proves that it makes no sense to try to describe the motion of each molecule separately from the point of view of Newton's dynamic equations. Although, the very large capabilities of modern computers to some extent allow this to be done. Similarly, when calculating powerful devices as magnetrons, klystrons and traveling wave tube (TWT), it does not make sense to describe the movement of each electron separately. Refers to trajectory calculations. When they go in a continuous stream, concentrated. A single, isolated electron can of course be calculated. But not in the case of electronic gas. Therefore, an approach that is based on the energy density distribution function w EMW (equation 4) can be very useful and practical. This theoretical and design model allows you to model and calculate all processes of energy power dissipation from various sources of type 4G and 5G and others.
The author expresses his readiness to cooperate if any organizations or people from all over the world show interest in these my scientific developments. We will implement and use together. Thank you for your attention.

Conclusions
1. The new idea that the continuous flow of HF EMW can be superimposed from the outside perpendicular to the alternating magnetic field rotating in a circle was physically substantiated. Which will cause the entire continuous flow of the HF EMW as a whole vortex cord to rotate. 2. Possible options for using this new technical installation for protective purposes, in defensive hostilities have been analyzed. In the form of electronic blocking of all combat vehicles, missiles and shells. It can also be used to block the physical and mental activity of soldiers by affecting the brain and other vital organs of human functional activity.

3.
A structural scheme for a refractive "lens for EMW" is proposed. 4. On the basis of gas-dynamic analogy semi-empirical formulas are obtained. Which allow to calculate spatial distribution of volumetric density of wave energy. In cylindrical coordinates (x, y).